ELITE FS 7 with No Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™ + charts – all at a

ELITE FS 7 with xSonic HDI M/H 455/800 Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™

ELITE FS 9 with Active Imaging 3-in-1 Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™

ELITE FS 7 with Active Imaging 3-in-1 Transducer (ROW) The new Elite™ Fishing System (FS) gives you access to the full line-up of Lowrance fishfinding tools – including ActiveTarget™ live sonar, Active Imaging™, FishReveal™ and preloaded C-MAP® Contour™ +

Surface mount kit for HS75 Antenna. Contains bracket to mount to compass, + 2 surface brackets. One mount for cables passing down through the mounting surface, and a taller version for feeding the cable out the side of the mount.

Pole Mount Bracket for HS75 - Standard 1'' 14TPI threads.

B&G Nemesis™ Hub allows compact and straightforward connection of up to 3 Nemesis™ displays at a key location (mast, helm etc) with a single Power/Ethernet cable run, and a simple interconnect cable from the hub to each display.

Side plate kit, GHOST 52”/GHOST 60”: 1x Cover mount RH, GHOST 52”/GHOST 60” 1x Cover mount LH, GHOST 52”/GHOST 60” 6x Screw, SHCS M4 x 0.7 x14, SS

Lower extrusion kit, GHOST 52”/GHOST 60”:1x Lower extrusion, with bushing, , GHOST 52”/GHOST 60”

Wear bearing kit, GHOST 52”/GHOST 60”: 2x Wear bearing, GHOST 52”/GHOST 60”

Lift assist kit, GHOST 52”/GHOST 60”: 1x Gas spring, compression/traction, GHOST 52”/60”, 2x Binding barrel, 5/16 x 1”, Pan, PH, SS, 2x Screw, 1/4-20 x 5/16”, Pan, PH, SS

Latch trigger, GHOST 52”/GHOST 60” 2x Latch trigger, GHOST 52”/GHOST 60”

Pushrod kit, GHOST 52”/GHOST 60”: 1x Clevis bracket, 4x Screw, M5x8mm, hex, button, SS, 1x Pushrod, finish machine with bushing, GHOST 52”/GHOST 60”

Upper extrusion kit, GHOST GHOST 52”/GHOST 60”: 1x Upper extrusion assembly, GHOST GHOST 52”/GHOST 60”

2x Nose cone O-ring, 1x Cable tie/heat shrink kit (not shown in the illustration), 1x Column, inner, GHOST 60”/lower unit (pre-assembled)

2x Nose cone O-ring, 1x Cable tie/heat shrink kit (not shown in the illustration), 1x Column, inner, GHOST 52”/lower unit (pre-assembled)

1x Column, inner shaft, 60"

1x Column, inner shaft, 52"

1x Cable, head to pedal, GHOST GHOST 52”, 2x Screw, M3 x 10, torx, 1x Seal, strain relief, 1x Cable tie/heat shrink kit, 1x PCBA thermal pad

1x Cable, head to pedal, GHOST 52”, 2x Screw, M3 x 10, torx, 1x Seal, strain relief, 1x Cable tie/heat shrink kit, 1x PCBA thermal pad

1x Lower housing assy with outer column, GHOST 60”, 1x Cable tie/heat shrink kit (not shown in the illustration), 2x Screw, M3 x 10, torx, 1x PCBA thermal pad

1x Lower housing assy with outer column, GHOST 52”, 1x Cable tie/heat shrink kit (not shown in the illustration), 2x Screw, M3 x 10, torx, 1x PCBA thermal pad

DDS Module - 4x 12-Pin Cables. For Initial prototyping or low-volume custom boatbuilders.

DDS-1 Dynamic Digital Switching - Simple (BoatBuilder Only)