Pushrod bushing kit: 2x Bushing bronze 5/8 x 1/2

Lower extrusion bushing kit 4x 1/2” Shaft bushing

Upper extrusion bushing kit: 2x Upper sleeve bushing 4x Rear pivot bushing

B744VC ACTIVE INSERT - REPLACEMENT

NSS16 evo3S is an all-in-one MFD, with built-in dual channel CHIRP sonar, GPS and WIFI. Support for chart options, Radars, Autopilot, Instrumentation and much more.

NSX 3009 - Smart Chartplotter / fishfinder. HDI Skimmer med/high 455/800 kHz transducer. No Chart. 9-inch SolarMAX™ high definition display, Built-in 1 kW echosounder, GPS, and WIFI. A next-generation C-MAP® DISCOVER™ X or REVEAL X™ chart card is required

NSX 3007 - Smart Chartplotter / fishfinder. HDI Skimmer med/high 455/800 kHz transducer. No Chart. 7-inch SolarMAX™ high definition display, Built-in 1 kW echosounder, GPS, and WIFI. A next-generation C-MAP® DISCOVER™ X or REVEAL X™ chart card is required

SONAR ADAPTER CABLE 9P MINI TO 9P

Pivot pin: 1x Pivot pin, pedal

Center cover kit: 1x Center cover, pedal, 1x Screw, no. 6x3/8, Phillips, pan, SS

Potentiometer kit: 1x Potentiometer, pedal, 1x Lock washer, 3/8", internal tooth, SS, 1x Nut, 3/8-32, SS, 1x Screw, no. 6x3/8, Phillips, pan, SS (not shown in the illustration), 2x Cable tie, anchored (not shown in the illustration)

GHOST foot pedal Configurable button 1 kit. 1 x Front left button assembly, pedal, 1x Spring, compression, 7mm ID x 15mm x 1m.

Housing, lower, pedal kit, 47”: 1x Base, pedal, 1x Wiper seal, pedal, 3x Grommet wires pedal, 1x Cable tie/heat shrink kit (not shown in the illustration), 1x Misc. hardware, pedal kit

Damper gear assembly kit: 1x Damper gear assembly, 1x Screw, cap, M4x16, 1x Screw, no. 6x3/4, torx, pan, ss

Label, battery: 1x Label status panel w/adhesive, pedal

PCBA, battery kit, 1x PCB TST ASY power/battery potted, 1x Cable tie/heat shrink kit, 3x Screw 7 mm torx T8

Front latch block: 1x Front latch block

Lower head adapter pin kit: 1x Pin bracket/bow arm, 1x Set screw, M6 x 8, SS

Secondary latch kit: 1x Secondary latch, 1x Spring, secondary latch torsion, 2x Washer, 1/2", nylon, 1x C-ring, 1/2", 15-7 PH SS, 1x Pull cable spacer

Upper extrusion kit with bushing, GHOST 47": 1x Upper extrusion assembly, GHOST 47"

Upper head adapter pin kit: 1x Pin, upper head, 2x E-clip, 1/2", 15-7 PH SS

Head adapter kit: 1x Head adapter with bushing

Lift assist spring kit, GHOST 47": 1x Gas spring, compression/traction, GHOST 47", 2x Binding barrel, 5/16 x 1”, Pan, PH, SS, 2x Screw, 1/4-20 x 5/16”, Pan, PH, SS

Lower dressing cap kit: 1x Lower dressing cap, 1x Spring, latch extension